Dirt bike grips are rubber or silicone grips that are mounted onto the handlebars of a dirt bike. For the rider, they are a crucial component of the bike that offers a comfortable and secure grip.
There are different types of grips available, such as soft or hard compounds, single or dual compound grips, and grips with various textures and patterns for increased traction.
Some grips may also have extra features such as vibration damping or raised ridges for added grip.
How To Choose The Dirt Bike Grips?
When selecting new grips, it’s important to consider factors such as the rider’s hand size and riding style, as well as personal preferences for grip feel and texture.
It’s also important to ensure that the grips are compatible with the bike’s handlebars and that they are installed correctly for maximum safety and performance.
Required Materials for Installation Of Dirt Bike Grips
For dirt bike grips installation, you will need the following materials:
New Grips: Obviously, you will need the new grips that you wish to install.
Lubricant: You will need a lubricant such as a grip glue or hairspray to help the grips slide onto the handlebars smoothly.
Clean Cloth: A clean cloth will be needed to wipe the handlebars clean and to remove any old adhesive or dirt.
Utility Knife or Scissors: A sharp utility knife or scissors will be needed to cut off the old grips and trim the new grips to the correct length.
Screwdriver: Depending on your dirt bike’s handlebar design, you may need a screwdriver to remove the end cap or any other screws or bolts that hold the grips in place.
Safety Gear: To protect your hands while removing old grips, you may want to wear gloves.
Make sure to read the instructions that come with your grips and follow the recommended installation procedure. Improperly installed grips can slip or twist during riding, which can be dangerous.
5 Steps For Installing Dirt Bike Grips
Sure, here are the steps for dirt bike grips installation:
- Remove the old grips: Use a sharp blade or a flathead screwdriver to carefully cut or peel off the old grips. You must be careful not to damage the throttle tube or the handlebar.
- Clean the handlebars: Use a clean cloth and some rubbing alcohol to clean the handlebars thoroughly. The purpose of this is to eliminate any dirt, grease, or residue that could hinder the proper adhesion of the new grips.
- Apply grip glue: Apply a small amount of grip glue on the inside of the new grips and the handlebars. try to use less glue, as it might cause the grips to slip or make them difficult to remove in the future.
- Install the new grips: Quickly slide the new grips onto the handlebars while the glue is still wet. Make sure the grips are straight and properly aligned with the throttle and clutch controls. Apply pressure to the grips until they are securely in place and keep holding them for a few minutes until the adhesive sets.
- Finish up: Trim any excess glue with a blade or a pair of scissors. Let the grips dry completely for at least 24 hours before using the bike. Subsequently, assess the grips by turning them to verify their firm attachment to the handlebars.
That’s it! By following these steps, you can install new grips quickly and easily.
Do’s And Don’t In The Installation Of Dirt Bike Grips
Installing new grips on a dirt bike is a simple task, but it’s important to do it correctly to ensure they are secure and comfortable to use. Here are some do’s and don’ts to keep in mind:
DO:
- Start by removing the old grips. You can either cut them off with a utility knife or loosen them with compressed air to achieve this.
- Clean the handlebar thoroughly with alcohol rubbing or another degreasing agent to remove any dirt, oil, or grease that could prevent the grips from adhering.
- Spread a small quantity of grip glue uniformly around the surface of the new grip’s circumference from the inside.
- Slide the grip onto the handlebar, making sure it’s straight and snug against the end of the bar.
- Maintain a firm grip on the handle for a few minutes to enable the adhesive to adhere.
- Repeat the process with the other grip.
DON’T:
- Don’t rush the installation process. Take your time to ensure the grips are properly aligned and secure.
- Don’t use too much grip glue, as it can make the grips difficult to remove in the future.
- Don’t use a lubricant such as WD-40 to install the grips, as it can cause the grips to slip on the handlebar.
- Don’t forget to check the fit of the grips before riding, as they can sometimes loosen during use.
- Don’t select grips that are damaged or worn, as they can be dangerous and affect your ability to control the bike.
By following these simple do’s and don’ts, you can install new grips with confidence and ensure a comfortable and safe riding experience.
FAQs On The Installation Of Dirt Bike Grips
Q1. What is the best way to clean my dirt bike grips before installation?
The best way to clean your grips before installation is to use a mild soap and water solution.
You can also use rubbing alcohol or a similar product. Be sure to rinse the grips thoroughly afterward to remove any residue.
Q2. How do I install my dirt bike grips?
To install your dirt bike grips, first, remove the old grips from the handlebars. In case the handlebars have any sticky residue, you can eliminate it by using rubbing alcohol or a comparable solution.
Next, apply a small amount of grip adhesive to one end of the new grip and slide it onto the handlebar. Repeat this process for the other grip. Allow the adhesive to dry for 24 hours before riding.
Q3. What is the best grip adhesive to use?
It is crucial to select a grip adhesive that works well with both your dirt bike grips and handlebars, considering the variety of options available in the market.
We recommend using a product like 3M Super 77 Multi-Purpose Adhesive or Gorilla Grip Adhesive.
Q4. How do I remove my old dirt bike grips?
To remove your old dirt bike grips, first, loosen the grip by twisting it back and forth while pulling it away from the handlebar.
In case the handle is firmly stuck, applying a small quantity of rubbing alcohol or a comparable substance can aid in loosening it. Once the grip is loose, pull it off of the handlebar. Repeat this process for the other grip.
Q5. Can I reuse my old dirt bike grips?
It is not recommended to reuse old dirt bike grips as they may not adhere properly to the handlebars and could come loose while riding.
Additionally, old grips may be worn or damaged, which could cause them to fail prematurely. If you must reuse your old grips, be sure to inspect them carefully for any damage or wear before installation.
Q6. Do I need to replace my dirt bike grips often?
Although it’s not mandatory to frequently replace your dirt bike grips, they will eventually require replacement as a result of natural wear and tear.
Inspect your grips regularly for any signs of wear or damage, and replace them when necessary.
Q7. What are some signs that my dirt bike grips need to be replaced?
Some signs that your dirt bike grips need to be replaced include: fraying at the edges, cracks or splits in the material, excessive wear, or if they become loose on the handlebars.
When you observe any of these indications, it is the right time to replace your grips.
